Good morning thread

[wøødɔhuɔk’ᴚ]

Coffee - lots of coffee before the nut house starts


2600 orders this morning - we’ll be well over 3500 be end of day


Gonna be a shit show from now through beginning of July


#letsgo

#morningbrad

 

[JRepairsK70e]

You just keep those bathrooms clean an operational !! 🤔🤗 an everthing should come out ok 👍

 

[BIGBADBOB]

mornin 36/70
have a great day

 

[Fifelaker]

Good morning. 46⁰/65⁰ and sunny. The workhouse is the plan.

 

[CFT]

Good morning Sawyers
40/73
Continue with project.
Damm I hate wind.

Saw safe

 

[rocketnorton]

ol sporty needs some miles

 

[wøødɔhuɔk’ᴚ]

Good morning 3d0wn3r

 

[Yukon Stihl]

Sup? good afternoon.

Finally come down from the pills?

 

[Yukon Stihl]

Morning
-7 C
Fuel day was uneventful, volumes reflect the warm weather plus lack of snow makes for a disappointing day. Hard work and low pay. Finished early set up the clutch on the rollback and topped up the tranny...

 

[Stihl sawing]

 

[DSS]

I'll take them stitches out for fiddy bucks

 

[Stihl sawing]

I'll take them stitches out for fiddy bucks

You take credit cards

 

[JRepairsK70e]

You gonna be able to grow hair back up there ??🙄😳🤦‍♂️

 

[JRepairsK70e]

You take credit cards

Yeth !! But doesn’t return em till they’re MT !! 🤗👍

 

[JRepairsK70e]

Booming cloudpiss moving thru the valley ,,spoza fuk oft by dahk !! Eyem inside checkin n prepping the trailer,yaks,bicycles,,sortin thru the “ dont leave home without “ tools n supplies ,,should be ready to head south by tues a.m. 🤗🤗👍😎🛶🚵‍♂️🎢⛺️

 

[cjcocn]

Good afternoon.

Aftermarket hubs are about half an inch too short so I packaged them back up and started a return for them.

I’ll pay twice (or more) the price tomorrow, but they will be the right ones and the Jeep will be back on the road.

Ball joints were bad, axle shaft u joint was bad, and the hub may have been okay but I separated it while removing it from the rust weld that was holding it on.

It’s going to ride nice when it is done.

 

[JRepairsK70e]

Good afternoon.

Aftermarket hubs are about half an inch too short so I packaged them back up and started a return for them.

I’ll pay twice (or more) the price tomorrow, but they will be the right ones and the Jeep will be back on the road.

Ball joints were bad, axle shaft u joint was bad, and the hub may have been okay but I separated it while removing it from the rust weld that was holding it on.

It’s going to ride nice when it is done.

Guess they saw the address 🤔🤔 and sent dimensionally proportionate parts !?🤷‍♂️🙄🤦‍♂️

 

[JRepairsK70e]

Curious ?? What measurement on the hub was to short ?? Eye’ve noticed some replacement hubs don’t fit into the spindle as far as Oe ,,,guessing they’re trying to lessen the amount of hub depth to have less surface to rust in place . Use a flap wheel on a die grinder to remove any rust on the “ bore “ of the spindle ,,the new hub should be able to easily slide in completely till the flanges meet ,,coat both the cleand spindle bore and the new hub flange and hub mount bolts with nevrsieze ,,justin case you’ve got to dismantle it again in the future ! 🤗👍🤞

 

[cjcocn]

Curious ?? What measurement on the hub was to short ?? Eye’ve noticed some replacement hubs don’t fit into the spindle as far as Oe ,,,guessing they’re trying to lessen the amount of hub depth to have less surface to rust in place . Use a flap wheel on a die grinder to remove any rust on the “ bore “ of the spindle ,,the new hub should be able to easily slide in completely till the flanges meet ,,coat both the cleand spindle bore and the new hub flange and hub mount bolts with nevrsieze ,,justin case you’ve got to dismantle it again in the future ! 🤗👍🤞

The flange where the wheel studs are held sits about half an inch lower.

So the distance between the flange that bolts to the knuckle and the flange that holds the wheel studs is too short.

 

[DSS]

41 and light rain. Morning Brad