Good morning thread
- Thread starter thomas1
- Start date
Good Morning All ! 37/47 , no sun ,no wynns , plenty of reign .
G’moorny990rs ,,32*earlier climbing into the mid 50’s ef an lingering thru tomally ?WTF? An it’s rainin alsew !🤨🖕! Mah arse was in the dentist chair by 7:10 ayem fora small repair on back ofa frt toof ,,numbnacaine had me thinkin the whole uppa lip was missing ,,tongue jus had to keep checkin 🤔🙄🤪quick stop fora doz fresh bagels n home by 8:15 👍😬. Gots neighbors lifted ‘06 Rubicon to dismantle a rear lower control arm to take measurements for a replacement heim style joint @ axle connection,,Rock Krawler can’t I D it by application ,,4 diff sizes and RH or LH thread versions could have been supplied back then 🤨🤔🤷♂️,,,gotta dew it sooner or later ,,,hope my oxy-acet bottles got some life in em !?🤷♂️🤔🖕🖕🖕
Im looking at upgrading my dust collection. I currently use a shop vac w/ a dust deputy but it fills up so damn fast and also doesnt get a lot of the good good from he bigger machines.
So my options that I'm looking at are:
Orrrrrrrr
2. A Grizzly G1029Z2P 2 HP Dust Collector with Aluminum Impeller - Polar Bear Series
www.grizzly.com
Single phase so no converter needed.
$679
The shop is 24x27 10ft ceilings.
Thoughts?
So my options that I'm looking at are:
- a USED 2019 MFG Powermatic PM1900TX-CK3
- https://www.ohiopowertool.com/brand...lters-and-dust-collection/powermatic-1792071k
- 3HP biggggg CFM but also BIG unit
- ~ $950
Orrrrrrrr
2. A Grizzly G1029Z2P 2 HP Dust Collector with Aluminum Impeller - Polar Bear Series
2 HP Dust Collector with Aluminum Impeller - Polar Bear Series at Grizzly.com
<h1>G1029Z2P 2 HP Dust Collector with Aluminum Impeller</h1> <h2>Rid your shop of fine dust particles.</h2> <p>This 2 HP Dust Collector with Aluminum Impeller is designed to capture dust and wood chips from woodworking machines, such as table saws, jointers and planers.</p> <p>The air drawn in...Single phase so no converter needed.
$679
The shop is 24x27 10ft ceilings.
Thoughts?
KFC sucksIm looking at upgrading my dust collection. I currently use a shop vac w/ a dust deputy but it fills up so damn fast and also doesnt get a lot of the good good from he bigger machines.
So my options that I'm looking at are:
It's a 3 phase unit which means I need to grab a VFD Single phase to Three Phase converter for like $200
- a USED 2019 MFG Powermatic PM1900TX-CK3
- https://www.ohiopowertool.com/brand...lters-and-dust-collection/powermatic-1792071k
- 3HP biggggg CFM but also BIG unit
- ~ $950
Orrrrrrrr
2. A Grizzly G1029Z2P 2 HP Dust Collector with Aluminum Impeller - Polar Bear Series
2 HP Dust Collector with Aluminum Impeller - Polar Bear Series at Grizzly.com
<h1>G1029Z2P 2 HP Dust Collector with Aluminum Impeller</h1> <h2>Rid your shop of fine dust particles.</h2> <p>This 2 HP Dust Collector with Aluminum Impeller is designed to capture dust and wood chips from woodworking machines, such as table saws, jointers and planers.</p> <p>The air drawn in...
www.grizzly.com
Single phase so no converter needed.
$679
The shop is 24x27 10ft ceilings.
Thoughts?
I was also told I was "lazy" by a 25 year old veteran of 25 seasons.
I've been called lots of things, 1st for lazy though.
did ewe tell him fuck off swizzle dick?