Good morning thread

JRepairsK70e said:
Booming cloudpiss moving thru the valley ,,spoza fuk oft by dahk !! Eyem inside checkin n prepping the trailer,yaks,bicycles,,sortin thru the “ dont leave home without “ tools n supplies ,,should be ready to head south by tues a.m. 🤗🤗👍😎🛶🚵‍♂️🎢⛺️
Click to expand...
What way you coming down? I-77 or I-85? If you are coming down I-85 I should slide over and meet up for lunch. Ive got several projects near I-85/I-40 merge in Graham/Hillsborough area. You still have my number?
 
  • Like
Reactions: edownr, Skeans1, BIGBADBOB and 7 others
cjcocn said:
The flange where the wheel studs are held sits about half an inch lower.

So the distance between the flange that bolts to the knuckle and the flange that holds the wheel studs is too short.
Click to expand...
Eye have never encounterd that much of a diff in dimensions on those types of components ,,,you must be used to a lil short ana week late scenario!! Prolly fit in the box bettah tho !🤗🤗👍👍🙄 Mebe mis boxed ??
 
Last edited:
  • Like
Reactions: greendohn, Skeans1, BIGBADBOB and 5 others
JRepairsK70e said:
Eye have never encounterd that much of a diff in dimensions on those types of components ,,,you must be used to a lil short ana week late scenario!! Prolly fit in the box bettah tho !🤗🤗👍👍🙄 Mebe mis boxed ??
Click to expand...
Boxed wrong is a real possibility. I got into a fck of a mess with ujoints in the wrong boxes once. Bought 2 and they didn't match but one of them was correct. So eye ordered another one but it turned out to be the one in the wrong box. :farkyou:
 
  • Like
  • Angry
Reactions: greendohn, edownr, JRepairsK70e and 5 others
JRepairsK70e said:
Curious ?? What measurement on the hub was to short ?? Eye’ve noticed some replacement hubs don’t fit into the spindle as far as Oe ,,,guessing they’re trying to lessen the amount of hub depth to have less surface to rust in place . Use a flap wheel on a die grinder to remove any rust on the “ bore “ of the spindle ,,the new hub should be able to easily slide in completely till the flanges meet ,,coat both the cleand spindle bore and the new hub flange and hub mount bolts with nevrsieze ,,justin case you’ve got to dismantle it again in the future ! 🤗👍🤞
Click to expand...
I never sieze everything too for the next guy...
sometimes it's me especially on my junk
 
  • Like
  • Love
Reactions: greendohn, Fifelaker, edownr and 4 others
Stihl sawing said:
20240414-081446.jpg
Click to expand...
Did you feel it when you spilled your coffee on your knee
 
  • Like
  • Wow
Reactions: greendohn, edownr, BIGBADBOB and 1 other person
Jimmy in NC said:
What way you coming down? I-77 or I-85? If you are coming down I-85 I should slide over and meet up for lunch. Ive got several projects near I-85/I-40 merge in Graham/Hillsborough area. You still have my number?
Click to expand...
Yeth !! We will be finishing the drive to Charlotte Weds morning from just south of DC ,,haven’t really lookd at the route from there yet ,,,Eyem guessing 95 south into NC then what ever Wayz suggests as most direct !🤷‍♂️Will check it later and reach out if there’s an opertunity we can shake hands 👍🤗
 
  • Like
Reactions: greendohn, Fifelaker, CFT and 2 others
You must log in or register to reply here.
Top Bottom
Back